![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
#1
|
|||
|
|||
![]()
Posted By: Matt
Today in the mail, I received 3 different SGC slabbed cards, from 2 different sellers. I was looking at the slabs a little closer then I usually do and noticed that the 2 slabs from one seller have 1/2" marks at the top and bottom of their cases where it looks like something was wedged in between teh two layers of plastic. Then I checked the 3rd card and found it also has a similar mark on the bottom of the case. Which leads me to: |
#2
|
|||
|
|||
![]()
Posted By: Matt E.
Just received 9 today and all of my SGC slabs have that same small mark on the ends of the holder. To me this is an indication where the plastic slabs were broken apart after being molded. No signs of anything else between the two layers. |
#3
|
|||
|
|||
![]()
Posted By: Dave F
PSA has them too...not sure about GAI or others |
#4
|
|||
|
|||
![]()
Posted By: Matt
That's what mine look like as well, so I guess it's nothing. Would the case look like if someone tried to pry it open? |
#5
|
|||
|
|||
![]()
Posted By: Peter Thomas
leaves a rough edge on about half of all SGC holders- top and bottom. I shave and sand them smooooth. |
#6
|
|||
|
|||
![]()
Posted By: JK
those marks are on every sgc slab I have. |
#7
|
|||
|
|||
![]()
Posted By: Marty
If a slab has been cracked and put back together, it should not be as structurally sound. Hold the slab in two hands, top and bottom. Twist in opposite directions and listen for cracking. Properly sealed from PSA or SGC, they will not crack. Do not use Magilla to twist. |
#8
|
|||
|
|||
![]()
Posted By: Ralph
Mine have the same marks in the same area on the holders |
#9
|
|||
|
|||
![]()
Posted By: Zinn
I think the marks are residue from the hermatically sealing of the holders. |
#10
|
|||
|
|||
![]()
Posted By: Eric B
Maybe it's where the machine holds onto the cases as they are sealed. |
#11
|
|||
|
|||
![]()
Posted By: Joann
They are mold gates. They are not related to the sonic welding. If you had two halves of a slab, in raw state never having been welded together, they would have these marks. |
#12
|
|||
|
|||
![]()
Posted By: T206Collector
...it's the mark of Voldemort! |
#13
|
|||
|
|||
![]()
Posted By: Steve Murray
perfectly logical explanation. So now all of you with paranoia may sleep easier tonight. |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Need help with cracking slabs | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 6 | 07-26-2008 01:43 PM |
PSA Slab Tampering | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 1 | 03-28-2008 07:04 PM |
Album Sheets for SGC slabs..? | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 4 | 03-25-2008 09:57 AM |
Slabs and UV Light | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 9 | 10-30-2007 09:47 PM |
Fakes, Trim Jobs and other signs of Tampering | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 6 | 03-10-2005 06:59 PM |