|
#1
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: DJ
|
#2
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: Keith O'Leary
dremel rotary tool.
|
#3
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: Peter_Spaeth
I have done it by using a pliers to crack the seal in the label area, then working very slowly along the edges with a very thin blade screwdriver to separate the two pieces of the holder. Similar to a PSA holder, just takes longer and more careful work. If BVG is like BGS the card is somewhat protected in a heat sealed inner sleeve which helps. |
#4
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: leon
For all holders I crack I take a wire cutter and crack an edge. I then take a sturdy flathead screwdriver and just pop the edges all of the way around it. Works like a charm.....good luck |
#5
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: Julie
and crack off pieces (not too close to the card. Start at the top where the label is, and when you have the label-part all off, ther two halves should come apart. If not, start carefully down the side, until they two parts do comer apart. |
#6
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: DJ
Thanks to the Board in assisting me. I got it out with your help without damage. I cracked the top with a hammer around the label and used a thin screwdriver to separate the plastic and safely (thankfully) removed the card without incident. Again, thanks! |
#7
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: Richard
for reference, there is an easier and faster way to crack a beckett case. It is a bit scary, but it works. |
#8
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: tbob
For a real challenge, try cracking out P-2 Sweet cap pins out of those little PSA holders. Arrrgghhhh! |
#9
|
|||
|
|||
How do I crack a card out of my BVG Beckett holder?
Posted By: Julie
At some point in the long, long past, I said here that the sleeves inside the PSA holders were NOT Mylar. Well, it's true, they are not Mylar in any protective sense, bump-wise. but they are very thin Mylar, called Mylite, which should keep the card safe from it's own plastic holder and anything that got inside of it, toning or yellowing wise... |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Should I crack a graded card out? | Archive | Postwar Baseball Cards Forum (Pre-1980) | 12 | 09-09-2008 11:28 AM |
Beckett BVG Grading | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 23 | 12-24-2005 09:32 AM |
Beckett eliminating subgrades for Vintage (BVG) | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 2 | 10-11-2005 12:34 PM |
cracking a BVG holder; any suggestions on how? | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 9 | 05-11-2004 09:51 PM |
Beckett takes the Low Road on BVG | Archive | Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions | 4 | 08-13-2003 06:21 PM |