Screw Your Gasket

Leon · #1 10-14-2018, 11:01 AM

Quote:

Originally Posted by ALBB

When I use a gasket, I prefer a little slippage

Speaking of a potential similarity, even if only metaphorically, is he holding a ball in his glove? That is sort of weird, and if so, I never really noticed that before and have owned a least 1-2 of that card over the years. What's old is new...or what I forget is new again

. And back to initial subject, that slabbing looks quite sturdy. If you put a seal around it you could make it waterproof too!!

frankbmd · #2 10-14-2018, 11:13 AM

Quote:

Originally Posted by Leon

Speaking of a potential similarity, even if only metaphorically, is he holding a ball in his glove? That is sort of weird, and if so, I never really noticed that before and have owned a least 1-2 of that card over the years. What's old is new...or what I forget is new again

. And back to initial subject, that slabbing looks quite sturdy. If you put a seal around it you could make it waterproof too!!

Waterproofing is an excellent idea, Leon. By the way what do you hold in your glove, if not a ball?

Peter_Spaeth · #3 10-14-2018, 01:08 PM

Quote:

Originally Posted by frankbmd

Waterproofing is an excellent idea, Leon. By the way what do you hold in your glove, if not a ball?

It's a gasketball.

Leon · #4 10-14-2018, 01:52 PM

Quote:

Originally Posted by frankbmd

Waterproofing is an excellent idea, Leon. By the way what do you hold in your glove, if not a ball?

It is the way the mitt is made (1900s period w/ individual fingers) which makes it look a bit strange. I recently bought a new glove so noticed it. Carry on...

brianp-beme · #5 10-15-2018, 01:09 AM

Frank could market this encapsulation idea under the name "A Complete Gasket Case".

Brian the Marketing Guru

irv · #6 10-15-2018, 03:51 PM

Quote:

Originally Posted by frankbmd

Whereas screwdown lucite holders may compress cards too much and "squeeze" the corners or damage the surface and,

whereas SGC gaskets, despite being preferred by many collectors, are associated with slippage of thinner cards behind or in front of the gasket in the SGC holder and,

whereas I am not willing to risk a costlier card that I want to display using either of these techniques, I offer the following:

Attachment 331228

Attachment 331229

Save the gaskets when you crack SGC slabs.

Place an appropriate gasket in a screw down lucite holder.

Carefully insert the card without a penny sleeve.

Replace the top of the screw down and tighten the screws as much as you like.

The gasket cannot be compressed. If the card fills the gasket as this one does, it will not slip, move or be compressed.

Hope that some of you may find this useful.

Good job, Frank, and pretty ingenious.

The only thing different I'd do would be to add some better looking screws. Those standards look too blah for that cube/card. Some nice bronze colored ones that fit flush would look much nicer, imo.

frankbmd · #7 10-15-2018, 05:03 PM

Quote:

Originally Posted by irv

Good job, Frank, and pretty ingenious.

The only thing different I'd do would be to add some better looking screws. Those standards look too blah for that cube/card. Some nice bronze colored ones that fit flush would look much nicer, imo.

I am a firm believer in personal preference when choosing screws.

irv · #8 10-16-2018, 10:01 AM

Quote:

Originally Posted by frankbmd

I am a firm believer in personal preference when choosing screws.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Some screw down holders	Peter_Spaeth	Everything Else, Football, Non-Sports etc.. B/S/T	2	04-30-2017 12:15 PM
Screw top holders	Snapolit1	Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions	17	01-02-2016 03:29 PM
Did I just screw up?	the 'stache	Net54baseball Vintage (WWII & Older) Baseball Cards & New Member Introductions	18	08-31-2014 09:56 PM
SGC gasket/liner/thingy wanted	Howe�s Hunter	T206 cards B/S/T	1	08-19-2014 10:46 AM
WTB: Screw down toploaders	karczewski	1950 to 1959 Baseball cards- B/S/T	0	12-12-2011 07:45 PM