Hey, pennant guys

[ooo-ribay]

Well. boys, it's a momentous day here in the "Hey, pennant guys" thread because I have figured out how you Heavy Hitters can frame your oversized pennants. If you look in the "September pickups" thread. you'll see my latest, low end acquisition. It measured 22 x 28, so I bought a cheap ($12) 24 x 36 poster frame and cut it down (I do this with both plastic and wood frames).

With the leftover plexi, I framed a small NYG pennant. You could do the same with oversized pennants. The only tools you need are shown in the photo (those and a straight edge). You could get one frame out of a 24 x 36 frame or two out of a 27 x 40. Unfortunately, you would not have enough "edging" for the two but, with a steady hand, wrapping the edges with black electrical tape wouldn't look terrible....at least not to a "low end" guy like me.

I really hope someone (Greg?) tries this and posts the results!

[thetahat]

Originally Posted by ooo-ribay

Well. boys, it's a momentous day here in the "Hey, pennant guys" thread because I have figured out how you Heavy Hitters can frame your oversized pennants. If you look in the "September pickups" thread. you'll see my latest, low end acquisition. It measured 22 x 28, so I bought a cheap ($12) 24 x 36 poster frame and cut it down (I do this with both plastic and wood frames).

With the leftover plexi, I framed a small NYG pennant. You could do the same with oversized pennants. The only tools you need are shown in the photo (those and a straight edge). You could get one frame out of a 24 x 36 frame or two out of a 27 x 40. Unfortunately, you would have enough "edging" for the two but, with a steady hand, wrapping the edges with black electrical tape wouldn't look terrible....at least not to a "low end" guy like me.

I really hope someone (Greg?) tries this and posts the results!

That’s awesome!!! You used a utility knife to cut the plastic and it cut easy without chipping? Great work. I have been doing this with 20 and even 40 gauge vinyl rolls. I made 5 holders from a rolls that cost $40 which was almost half shipping. This looks fantastic.

And I should add that it’s an awesome pennant, too!

[thetahat]

I am definitely going to try this, Rob ... here is one of my vinyl holders which is soft but much thicker than soft sleeves. I’m also doing this for my minis which I am now collecting ...

[perezfan]

Originally Posted by thetahat

I am definitely going to try this, Rob ... here is one of my vinyl holders which is soft but much thicker than soft sleeves. I’m also doing this for my minis which I am now collecting ...

Gee Greg...

Couldn't you pick a better pennant to demonstrate your vinyl holder?

[thetahat]

Originally Posted by perezfan

Gee Greg...

Couldn't you pick a better pennant to demonstrate your vinyl holder?

Ha .... yes this is one of my favorites, everything is stitched including the elephant. No paint.

[ooo-ribay]

Greg - I’d probably pop for the acrylic cutter. It drags out a little curl of plastic as you pull it towards you. The utility knife might work but it also might be too fine.

[thetahat]

Two recent pickups. Athletics is unknown year, but I suspect it is early 1930s at the latest. Maybe late teens? Very thick, soft felt. Normal size pennant. Red Sox is a Keezer, I guess they did multicolor only for local Sox. I found it interesting that despite having a spine, the tassels were stitched on the outside.

[ooo-ribay]

Originally Posted by thetahat

That’s awesome!!! You used a utility knife to cut the plastic and it cut easy without chipping? Great work. I have been doing this with 20 and even 40 gauge vinyl rolls. I made 5 holders from a rolls that cost $40 which was almost half shipping. This looks fantastic.

And I should add that it’s an awesome pennant, too!

The little yellow tool is a plexiglass cutter. It basically scores the plexi, which then snaps cleanly. The plexi that comes in those cheap poster frames is very thin but I’ve also used this tool on heavier plexiglass (a 4’ x 8’ sheet). The utility knife would probably work on the thin stuff although the yellow tool only cost a few bucks. I used the utility knife to cut the cardboard backing and the “frame.”